Greenleaf Logo
Greenleafeco-friendly • sustainable
Weak Flame or No Gas? A Troubleshooting Guide for Biogas Owners.
Education

Weak Flame or No Gas? A Troubleshooting Guide for Biogas Owners.

Greenleaf TeamOctober 31, 20265 min read

A biogas system that has been running well for months can suddenly start giving a weak, yellow or flickering flame — or no gas at all. It's one of the most common calls we receive, and the good news is that most causes are simple, inexpensive to fix, and can be checked by the household without any special tools.
This guide walks through the problems we see most often, in the order we'd check them on a service visit.

Start by reading the flame

The flame on your burner tells you a lot about what's happening in the system. A healthy biogas flame is steady, quiet and mostly blue. If yours looks different, it usually points in one of three directions:
A yellow or orange flame usually means the gas and air aren't mixing properly. Check that the burner's air inlet isn't blocked by food residue or dust, and that the burner cap is seated correctly.
A small, flickering flame that sometimes goes out usually means low gas pressure — something between the digester and the stove is restricting flow, or the digester isn't producing as much as it should.
A flame that lifts off the burner or won't stay lit, especially on a newly started digester, often means the gas contains too much carbon dioxide. This is normal in the first weeks after start-up and settles as the bacteria establish themselves.

Check for water in the gas line

Biogas leaves the digester warm and carries water vapour with it. As it cools in the pipe, that vapour condenses and collects at the lowest points in the line. Over time, enough water builds up to partly block the pipe — and the result is a weak, sputtering flame even though the digester is producing plenty of gas.
If your system has a water trap or drain valve, open it and let any collected water out. This should be part of a regular routine, more often during cold months when condensation is heavier. If your pipe sags anywhere between the digester and the kitchen, it's worth having it re-routed so water drains naturally rather than pooling.

Look at how the digester is being fed

Gas production depends on the bacteria inside the digester having a steady supply of food. Most drops in output we see trace back to a change in feeding:
Skipped days or irregular feeding. The bacteria work best with a consistent daily routine. A few missed days will show up as lower gas output soon after.
The wrong mix of waste and water. For cattle dung, a roughly equal mix of dung and water is a good starting point. Too thick, and the mixture doesn't flow well through the tank; too watery, and there isn't enough material for the bacteria to work on.
Harmful material entering the tank. Detergents, disinfectants, and dung from animals recently treated with antibiotics can slow down or kill the bacteria that produce gas. Keep these out of the inlet wherever possible.
Overfeeding. Adding far more than the digester was sized for doesn't produce more gas — it can push material through the tank before it has finished digesting, and output drops.


Cold weather slows everything down


The bacteria in a digester are most active in warm conditions. During cooler months — and in higher-altitude areas with cold nights — gas production naturally falls, sometimes noticeably. This isn't a fault with the system.
You can soften the effect by keeping feeding consistent, using warm water in the mix where practical, and making sure the area around the digester isn't waterlogged. Production recovers as temperatures rise.


Don't overlook the fittings and burners


Raw biogas contains small amounts of hydrogen sulphide, a corrosive gas that slowly attacks metal burners, valves and fittings. Over time, burner holes can clog and fittings can begin to leak. A desulphurizer fitted on the gas line removes most of it before it reaches your appliances, and replacing its filter material on schedule is one of the easiest ways to extend the life of your stove.
It's also worth checking that every valve between the digester and the stove is fully open, that the flexible pipe hasn't been kinked or crushed, and that burner ports are clean. A small brush or pin is usually enough to clear blocked holes.


How to check for leaks safely


If production seems normal but less gas is reaching the kitchen, there may be a leak along the line. To check, brush soapy water over joints, valves and connections while the gas is on. Bubbles forming at any point show where gas is escaping.


Never use a match or lighter to look for a leak. If you smell gas indoors, close the main valve, open doors and windows, and don't switch on lights or light any flame until the smell has cleared.

When to call a technician

Some problems need a trained eye. Contact us if gas output stays low for several weeks despite regular feeding, if you see slurry overflowing or not moving through the outlet, if you find cracks or wet patches around the dome, or if you smell gas and can't find the source.
Our team handles servicing, repairs and replacement parts for all types of biogas systems. If something doesn't look right, reach out — it's always cheaper to fix a small issue early than a larger one later.